Display - Communications

  • R367.40

    SolarEdge S0 meter adapter cable

    Add to cart
  • R703.39

    Samil Solar River TL-S RS485 Ext. Card

    Now distance can be bridged easily with Samil’s Solar River Extension Card – suitable for the TL-S range. This retrofit allows wireless contact between two sections of a PV plant with RS485 communication. It can be used where laying cable would be impossible.

    Add to cart
  • R721.21

    SAMIL SOLAR LAKE TL-PM RS485 EXTENSION CARD

    Now distance can be bridged easily with Samil’s Solar Lake Extension Card – suitable for the TL-PM range. This retrofit allows wireless contact between two sections of a PV plant with RS485 communication. It can be used where laying cable would be impossible.

    Add to cart
  • R751.99

    SAMIL SolarRiver TL-S WIFi card

    The SAMIL SOLAR RIVER TL-S WIFI EXTENSION CARD retrofit is a clever, simple, external plug-in device, which is fully universal across the Solar River TL-S range.

    The installation is very straight forward and only requires the installer to have a smartphone/laptop to hand; the only customer requirement is a WIFI network within range of the inverter.

    The unit provides a user friendly, easily accessible solution to inverter monitoring.

    Add to cart
  • R993.38

    ZIGBEE INVERTER SLAVE KIT Type 5

    Connects SolarEdge inverters wirelessly to an Internet router using the ZigBee protocol.

    This ZigBee unit is installed within the inverter enclosure for outdoor resilience and the antenna external to inverter for wider range.

    The Home Gateway is required to complete the communication. This part is only the ZigBee adaptor for the inverter and can be used to expand the one-inverter coverage offered by the SE-1000-ZBGW-K

    The Home Gateway supports up to 15 SolarEdge devices (e.g. inverters) on the wireless network.

     

    Add to cart
  • R1,301.01

    Device Control ZigBee Module

    Supplier Part No:SE1000-ZB06-MOD

    Weight:0.34 kg

    Add to cart
  • R1,441.30

    SMA 485 Data Module Type B ( for STP-20 only )

    The 485 data module enables you to setup cable-connected RS485 communication and is compatible with the SMA TL-20 range of three phase inverters.

     

    Add to cart
  • R1,441.30

    SMA RS485 Interface

    Compatible with SMA inverters with a low frequency transform SB-1200, SB-1700, SB-3000 and SB-3300 and the transformless inverters SB-1300, SB1600 and SB-2100

     

    Add to cart
  • R1,441.30

    SMA RS485 Interface ( for SB-TL21 & STP-30 )

    Technical Data

    Communication interface RS485

    Maximum wireless range 1,200 m

    Width x height x depth: 33 mm x 62 mm x 34 mm

    Weight 23.8 g

    Installation location SI 8.0H and SI 6.0H

    Add to cart
  • R1,517.97

    Modbus Server For OmniPower Inverter

    Embedded with web server
    Monitor and operate up to 247 modbus devices with a single device
    Ideal monitoring solution for medium sized solar plants
    Optional External Modbus Web box Server for Omnipower 3KW and 5kW single phase inverters
    Optional External Modbus Web box Server for Omnipower Plus 10KW 3Phase inverter.

     

    Add to cart
  • R1,871.82

    Solar-Log Split CT 250A

    Functions
    Local monitoring
    Local graphical reports via a web browser
    LCD-Status-Display
    Status display for installation and operations.
    Solar-Log™ Easy Installation
    The inverter detection and Internet registration are carried out immediately. The installation
    mode is indicated on the LCD-Status-Display. It is possible to configure the Solar-Log® via
    the PC Web interface.

    Add to cart
  • R1,934.91

    Steca Smart Energy Manager

    Smart Energy Manager for coolcept, coolcept-x, coolcept³, coolcept³-x, StecaGrid 8000+ 3ph and 10000+ 3ph
    The feed-in management solution
    The StecaGrid SEM offers different options of realising feed-in management with a photovoltaic system. A ripple control receiver from the relevant distribution grid operator can be connected. From firmware version 3.0, the feed output at the grid connection point can be limited to an adjustable value, or the ripple control signal can be switched to the relay output. The individual operating modes are selected and defined via the free StecaGrid User PC software. Up to ten inverters can be connected to the StecaGrid SEM via the RS 485 interface.
    Easiest installation
    StecaGrid SEM can be installed in the switching cabinet right next to the ripple control receiver. The casing features a dimensioning typical for switching cabinets and can be mounted onto a top-hat rail. Its width is 4 HP. Direct power supply at 230 V. A mains adapter plug or an external direct current power supply are not required.
    Easily accessible service interface
    All connected StecaGrid inverters can be accessed via a USB interface on the StecaGrid SEM. Connection to a PC is possible via a standard USB cable. The interface is on the front side of the casing – the cover does not need to be removed in the switching cabinet.
    The StecaGrid SEM can be configurated via the StecaGrid User Software (from version 3.0). The  software is available at www.stecasolar.com from free download.

     

    Add to cart
  • R2,001.26

    Solar-Log Split CT 100A

    Functions
    Local monitoring
    Local graphical reports via a web browser
    LCD-Status-Display
    Status display for installation and operations.
    Solar-Log™ Easy Installation
    The inverter detection and Internet registration are carried out immediately. The installation
    mode is indicated on the LCD-Status-Display. It is possible to configure the Solar-Log® via
    the PC Web interface.

    Add to cart
  • R2,009.51

    SMA Web Connect ( SWDM-10 )

    Webconnect provides free access to Sunny Portal without additional data logger – easily via an existing Internet access and a DSL router. After the simple installation of the inverter interface which is optionally available or already integrated at the factory, you can commission the Webconnect.

    Connections: Ethernet RJ45

    Max. radio range: Ethernet 100 m

    The Webconnect function enables data transmission between the Internet portal Sunny Portal and the inverters. Data transmission takes place via a router with Internet access. A PC with the software Sunny Explorer* is also connected to the router.
    * as of software version 1.04. Sunny Explorer is available free of charge at

    The Webconnect Data Module performs the following tasks:
    • Set-up of a Speedwire network
    • Data exchange with the Internet portal Sunny Portal and Sunny Explorer via a router

    Add to cart
  • R3,621.23

    1PH/3PH 230/400V SolarEdge Modbus Meter 1 second K1

    The Modbus meter requires CTs to function. Please choose the appropriate current capacity from the Modbus range here, or you can copy and paste this link into your browser: http://portal.segen.co.uk/nav/pv/-brand-solaredge/CurrentSensorClamps

     

    Add to cart
  • R3,646.41

    Solar-Log 3 Phase Meter, MID, RS485 Current Transformer-connected

    A power meter relays the measured amount of power to the Solar-Log™ for analysis.

    If you wish to consume the self-produced power from a PV plant, the meter serves as a consumption meter, displaying a comparison of the power produced and consumed.

     

    The meter can be configured to operate with the Solar-Log™ in three different modes:

     

    1. Measuring power consumption for the optimal utilization of self-produced power.
    2. Measuring the total amount of power that has been fed into the grid.
    3. Measuring the power production from inverters that are not directly supported by Solar-Log

     

    This is the CT version of the PRO380 energy meter.

    Use the Solar-Log CTs with this meter; rated from 100-500A.

    Add to cart